Hello everyone! As of today, we have 90 registered! That's going to be a great turn out!
Just a reminder that rally registration closes on May 9 so that we can place our t-shirt order for the rally.
If you are coming, but have not sent in your registration, do it TODAY or TOMORROW!
After that, we will not accept any orders for t-shirts. We order a few extra of the most common sizes for the rally. You can only get what is available.
Have you all made your hotel reservations? If not, do it NOW! If our blocked rooms are full at Laquinta Inn, you'll have to find other lodging.
See you all soon!
Got a tech tip for Voyager 12's from your personal experiences, or one complete with pictures and instructions, here's where to post it. You can also ask about tips or procedures here.
Ok, my brother and I were out riding yesterday - about 150+ miles. Bike ran fine for most of the run, but as we hit the slab for the last 15 miles or...
I have been having various electrical issues which ultimately traced back to a very corroded 10 pin connector.
My rear wiring harness was hacked...
Last post
On both my bikes I went thru all the relays before I hard wired the 10 pin connectors and replaced them all with Toyota denso relays which cost me a...
After getting my bike out of the back of the garage from it's winter slumber, the headlight will not come on. Any ideas on where to look first? I am...
Last post
corrosion on the terminals increases resistance and can blow a fuse. I suggest spraying all connectors with electrical contact cleaner and follow up...
To date I have had a 77 Yamaha XS750
92 and my new current bike a 1998 Concours 1000
1984...
Last post
My first real ride today. Well, short one at only 12 miles but it was on the highway and loved it. Still things to sort out as the clutch fluid needs...
So on the maiden test ride around the housing development after rebuilding a 20yr old XII, I discovered a lazy speedometer. The needle responded, but...
Last post
Thank you for sharing your experience :woohoo: I don't think I would have been as calm as you were if I did an unindexed disassembly :gig:.I have...
I just pulled the rear tire if my 87 1200 voyager and am going to have it replaced. It is currently a bridgestone on there now with a bridgestone on...
Last post
bob if you order some speed bleeders, little one way valves that replace the standard bleeders you can easily change out your fluid without hassle...
So here it is again was going to change the oil in my 1200 and was wonder if any one knew the difference between the Rotella T and the T4 I see that...
Last post
Be careful on the viscosity... I ran the Full Synthetic T6, for a while, but then I started having shifting issues. The T6 is 5 W-40, so it is too...
Well I've search for a tire (darkside) to fit my voyager. Walmart doesn t have 165/80-15 available anymore, nor does belletire or discount tire. The...
Last post
Put new tires on last spring ,,,The rear tire is for a 1962 Volkswagen from www.DiscountTireDirect.com ...........
here is part of the...
Bike is going to shop soon ,I have done oil and rear end change,looking at brake and clutch fliud change,nrake pads front and back.Progessive springs...
Last post
After you get the bike back
Add
lube kick stand pivot bolt
Adj and lube cruse control cable (it's simple after you remove the faring)
fuel filter...
Friends, I back.
Because my bike fall (one _______(edit by webmaster) hit my fender :tho: ) I lifted her and turn on the engine, when one boy that...
Last post
I saw on ebay some cylinder head but I am speaking with forum member that have one to I buy. One engine I believe that no easy send to me, because of...
Looking over an old audio topic on upgrading the audio system today got me thinking. I have been looking at a Kenwood BT amp to use on my Harley and...
Last post
I received an email from Kenwood stating the amp has a 15A current consumption.
I have kept randallor's post of broken clutch cover bolts, dated April 17-2015,in my mind since he posted the problem and the results.This fall I...
Last post
Should one encounter a small diameter screw/bolt which is uncooperative in coming out, I have found that my DeWalt 1/4 18 Volt impact driver and the...
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
