Got a tech tip for Voyager 12's from your personal experiences, or one complete with pictures and instructions, here's where to post it. You can also ask about tips or procedures here.
BLUF - What happens when you mix a Metzler 880 rear tire with an Elite or a Venom front tire?
We have an essentially new Metzler 880 on the rear;...
Last post
Thank you for the advise. We will probably buy either a Venom X or an Elite III front tire before we go to New York (I hope we can find the time and...
So there I was trying to figure away around removing the air box when syncing the carbs. No way you gotta remove the box, go ahead and just pull it....
Last post
Had an afterthought. I think I'll go buy a single valve. I found one for under $10. Then I can use that in conjunction with my one at a time line...
Does anyone use a moly additive in their rear drive? It is recommended in my Guzzis where I have used it for many years. I can't see a problem adding...
Last post
How often do you all change your gear oil?
I do it first thing every spring (5-7k miles)
I think the book says change every 40,000 miles....
OK, so I managed to break the lever off of the first stage of the center stand. I want to remove the 1st stage to weld a new lever on. Now that it is...
Last post
For those interested, there are 3 center stands which just popped up on E-bay. They are listed for the ZN-1300, but I checked the part number and...
Morning. It has been a while, and now i'm back. Can i change my leaky valve cover gasket without removing the engine. And also, i need to change the...
Last post
Searching through my collection of o rings, i was able to find four to do the job. Thank God i didn't have to pay Kawy,,, $2.10 each... Once all...
The wire bundle that goes from the igniter, forward along the right side of the frame toward the front of the bike gets rubbed every time I remove or...
Rick wanted me to post up some pics of his handywork. He has some of those chrome vent covers on his Voyager XII. What he did, was to grab some...
Last post
Do you happen to have a template for those covers? Is there another alternative if you do not have the chrome covers? I tried a fridge magnet and of...
Has anyone had any experiences with these turn signal conversion kits? It looks interesting, but I really wonder how they do this....especially thru...
Last post
I went to my local NAPA store and bought the sockets there, then installed and wired them up. Not a difficult job.
Our Voyager is doing OK overall but we have slid a little here and there recently and sometimes the front end is loose. On the occasions we have lost...
Last post
I just got back from the dealer today. I ended up spending over $200 in combined service and more parts ($70 for a pair of EBC brake pads). When they...
Just wondering if someone might have pictures of the Rivco style air horn mounts. I have a slightly larger set of air horns that won't fit where I...
Last post
I know most understand that the Rivco Horns are all the same, but the mounts are different for Make/Model. I do know that one of the Goldwing set-ups...
I am going to hard wire my front and rear together. The fader has caused problems in the past and when I am sitting still it is nice to have all four...
Last post
I've usually found if you spray the pot control with electrical cleaner that is solves the glitching problem. Never tried it on the Voyager but from...
Does anyone have any problem with the choke not really working? On my '89 the choke will work when set at about 1/2, but only for one try. If I don't...
Last post
Have you checked the condition of your spark plugs lately? Half fouled or worn plugs could cause this assuming your choke and all else is ok. I also...
This is not for the faint of heart, but I thought I'd share the info just in case. I had found the perfect voltmeter some time back, but when the 3rd...
Last post
I could win for best use of duct tape and bungee cords :bat:
I am about to embark upon an OEM CB installation on my 2000 XII. How does one go about checking the SWR with the OEM antenna? I don't know of any SWR...
Since I already had a quart of Mobil One Synthetic I just bought three more quarts for my last oil change with Mobil One. No problems with Mobil One...
Last post
The correct process for choosing an oil for a particular engine is to look at the API rating that is recommended in the manual that goes with the...
Just bought a really clean 01 with custom (i.e., not factory colors) paint job and lotsa shiney chrome. It has a couple functional issues though and...
Last post
On the 01, I pull in the clutch, even in neutral I think, and the bike will not start. .
Mine acted like this since I bought the bike this...
Just wondering what you have done to clean or dress up the front fork tubes. I just purchased a very nicely painted and dressed 01 and about the only...
Last post
I told my buddy that this was a very good price for this year bike. He wasn't too concerned that he did not get it because he said there will be...
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
